BMW DIAGNOSTIC TROUBLE CODES (DTC) All 1989-94 BMW vehicles are equipped with a self diagnostic system for the detection of injection faults. When a fault is detected by the system the Electronic Control Unit (ECU) records the code corresponding to the defect in the ECU's memory until either: MOTRONIC 'PEDAL' FAULT CODES (CARB). Workers Compensation Code 2883. See the NCCI basic manual phraseologies for workers compensation code 2883 on the bulleted item(s) below. If you have a classification question or believe you have been incorrectly classified, please see The Employer’s Workers Compensation Classification Guide.
BMW: Accessing Trouble Codes
This information applies to 1989-19903, 5, and 7 series BMW models.
The following procedure will enable you to retrieve “basic”or “flash” trouble codes only. Other codes may also be stored, but theycan only be retrieved using an appropriate Scan Tool.3 SeriesTurn the ignition key to the “on” position, but do
notstart the engine. Wait 3 seconds for the code(s) to flash. Thecheck engine light will flash the first code, pause for 3 seconds, thenflash the next code. For example, if codes 2 and 4 are stored, the checkengine light will flash twice, pause for three seconds, then flash fourtimes. When all codes have been displayed, the check engine light will remainON.Code Definitions
| Code 1 | Airflow Meter |
| Code 2 | Oxygen Sensor |
| Code 3 | Coolat Temperature Sensor |
| Code 4 | Throttle Position Sensor |
Less Diagnostic Tool
Bmw Code 2883 Download 2017
90-later 3 series models
- Turn ignition On.
- Depress accelerator pedal five times to WOT within five seconds.
- DTCs will display as flashes on ‘‘Check Engine’’lamp.
- On models equipped with V-12 engine, depress accelerator pedal six timesto WOT to display cylinder 7–12 DTCs.
First digit (always “1”), pause, 2nd digit, pause, 3rd digit,pause, 4th digit. The light will now pause again and then will begin flashingout the next stored code, or it will repeat the first code if no other codesare stored.| 1000 | End of diagnosis |
| 1211 | Electronic Control Unit (ECU) |
| 1215 | Airflow Sensor |
| 1221 | Oxygen Sensor |
| 1222 | Oxygen Sensor regulation |
| 1223 | Coolant Temperature Sensor |
| 1224 | Air Temperature Sensor |
| 1231 | Battery Voltage out of range |
| 1232 | Idle Switch |
| 1251 | Fuel Injectors (final stage 1) |
| 1252 | Fuel Injectors (final stage 2) |
| 1261 | Fuel Pump Relay |
| 1262 | Idle Speed Controller |
| 1263 | Tank Vent |
| 1264 | Oxygen Sensor heater relay |
| 1444 | No faults in memory |
Using Scan Tool
Connect scan tool to diagnostic link connector located at right rear ofengine compartment. Follow tool manufacturer’s instructions to obtainDTCs.Reading the Trouble Codes
Using Check Engine Lamp
‘‘Check Engine’’ lamp will stay on five seconds, flashonce, then begin flashing fault codes with 2.5 seconds between numbers. WhenDTC has been displayed, lamp remains on. Repeat access procedure to displaynext DTC. If first DTC is 1444, 2444 or 4444, no DTCs are stored. DTC 1000or 2000 followed by one or two flashes, a long paused and then lamp remainingon indicates no more DTCs are stored. Refer to ‘‘Diagnostic TroubleCode Identification’’ for DTC interpretation.Clearing Trouble Codes
To clear trouble codes, momentarily disconnect multi-pin connector fromECM, disconnect battery, start engine 60 times after repair without repeatfailure, or follow diagnostic tool manufacturer’s instructions.NOTE: IF YOUR CAR IS EQUIPPED WITH A FACTORY ANTI-THEFT RADIO, MAKESURE YOU HAVE THE RADIO ACTIVATION CODE BEFORE YOU DISCONNECT THE BATTERYCABLE!Bmw Code 2883 Download For Mac
| Model | Year | Engine identification | System |
|---|---|---|---|
| 1 Series (E82/E88) | 2008 | 6 cylinder N51 | Siemens |
| 3 Series/Compact (E36) | 1992-01 | 4 cylinder | Motronic/Siemens |
| 3 Series (E46) | 1998-02 | 4/6 cylinder | Motronic M5.2/ME7.2/ BMS46 |
| 3 Series (E46) | 1998-02 | 4/6 cylinder | Siemens MS40/41/42 |
| 3 Series 2.5/3.0L (E46/E90/E91) | 2002-06 | 25 6S 6/30 6S 3/N52/N53 | Motronic/Siemens |
| 3 Series 3.0L (E90/E91/E92/E93) | 2007-08 | 6 cylinder N51/N52 | Siemens |
| 3 Series 3.0L (E90/E92/E93) | 2007-08 | 6 cylinder N54 | Siemens |
| 5 Series (E39) | 1996-02 | 6/8 cylinder | Motronic/Siemens |
| 5 Series 2.5/3.0/4.4/4.8L (E39/E60/E61) | 2002-06 | 25 6S 5/30 6S 3/44 AS 1/2/N52/N53/N62 | Motronic/Siemens |
| 5 Series 3.0L (E60/E61) | 2007-08 | 6 cylinder N52 | Siemens |
| 5 Series/M5 3.0/5.0L (E60/E61) | 2006-08 | N54/S54 | Siemens |
| 5 Series 4.4L (E60) | 2004-05 | N62 B44 | Motronic/Siemens |
| 5 Series 4.8L (E60/61) | 2007-08 | N62TU | Motronic |
| 5 Series M5 5.0L (E39) | 2000-03 | 50 as 1 | Motronic/Siemens |
| 5 Series M5 5.0L (E60/61) | 2006-08 | S54 | Motronic/Siemens |
| 6 Series 4.4/4.8L (E63/E64) | 2004-06 | N62 | Motronic/Siemens |
| 6 Series 4.8L (E63/E64) | 2007-08 | N62TU | Motronic |
| 6 Series M6 5.0L (E63/E64) | 2006-08 | sa5 | Siemens |
| 7 Series (E38) | 1994-02 | 6/a cylinder | Motronic/Siemens |
| 7 Series 4.4/4.8L (E65/E66) | 2002-06 | N62 844/8a5 | Motronic/Siemens |
| 7 Series 4.8L (E65/E66) | 2007-08 | N62TU | Motronic |
| 7 Series 6.0L (E66) | 2003-08 | N73 | Motronic |
| 8 Series (E31) | 1994-98 | a/12 cylinder | Motronic/Siemens |
| X3 2.5L (E83) | 2004-05 | 25 6S 5 | Motronic/Siemens |
| X3 3.0L (E83) | 2004-06 | 30 6S 3/M54/N52 | Motronic/Siemens |
| X3 3.0L (E83) | 2007-08 | 6 cylinder N52 | Siemens |
| X5 (E53) | 1999-02 | 8 cylinder | Motronic/Siemens |
| X5 3.0/4.4/4.6/4.8L (E53) | 2003-06 | 30 6S 3/44 8S 2/46 a8 1/N62 844/N62 B48 | Motronic/Siemens |
| X5 3.0L (E70) | 2007-08 | 6 cylinder N52 | Siemens |
| X5 4.8L (E70) | 2007-08 | N62TU | Motronic |
| Z3 | 1996-02 | 4/6 cylinder | Motronic/Siemens |
| Z4 2.5L (E85) | 2003-05 | 25 68 5 | Motronic/Siemens |
| Z4 3.0L (E85) | 2003-08 | 30 68 3 | Motronic/Siemens |
| Z4 3.0L (E85/E86) | 2007-08 | 6 cylinder N52 | Siemens |
| Z4 3.0L (E85/E86) | 2006-08 | 6 cylinder 854 | Siemens |
| Z8 5.0L (E52) | 2000-03 | 50 8S 1 | Motronic/Siemens |